MenuMENU

FAQ – DIY Spectrometer

What wavelength range is the DIY spectrometer suitable for?

EURECA's DIY spectrometer was initially developed for experiments in the visible spectral range (VIS, approximately 400–700 nm). However, the Toshiba TCD1304DG linear CCD sensor used in the system is also sensitive to near-infrared (NIR) radiation.

According to the manufacturer's specifications, its spectral sensitivity extends to approximately 1000 nm, although it decreases significantly towards longer wavelengths. EURECA has already successfully detected infrared LEDs with emission wavelengths of up to 950 nm.

The actual usable spectral range of the spectrometer depends not only on the sensor but also on the selected optics, diffraction grating, alignment, and signal intensity. Our development work and documented experiments to date have primarily focused on the visible spectral range.

Extending the system into the UV or NIR range is possible in principle, but its suitability must be verified experimentally for each specific application.

Can the DIY spectrometer also be used for UV spectroscopy?

The standard CCD sensor used in the DIY spectrometer has only limited sensitivity at wavelengths below approximately 400 nm.

However, EURECA has developed a special process for the UV conversion coating of image sensors. This involves using a luminescent coating to convert incident UV radiation into visible light that can be detected by the sensor.

In principle, this technology makes it possible to use the DIY spectrometer for UV measurements as well.

However, a complete UV spectrometer also requires consideration of other components, particularly the diffraction grating, mirror coatings, entrance slit, and any optical fibers used.

A DIY spectrometer modified in this way should therefore be regarded as an experimental extension. The achievable UV sensitivity and usable wavelength range depend on the specific configuration.

Can I use the DIY spectrometer for transmission and absorption measurements?

Yes. The DIY spectrometer is suitable in principle for transmission and absorption measurements and allows users to build their own experimental setups.

In a transmission measurement, the spectrum of light passing through a sample is compared with a reference spectrum recorded without the sample. The spectral transmittance can be calculated from the ratio of these two spectra, and the absorbance can then be determined.

Typical applications include the investigation of dye solutions, optical filters, and transparent materials.

Further information on the measurement principle, the calculation of spectral transmittance, and practical experiments can be found in our article on transmission spectroscopy.

Our experiments to date have primarily focused on the visible spectral range. Measurements in the near-infrared are also of interest due to the sensor's characteristics, but have not yet been systematically investigated by EURECA.

Quantitative measurements require appropriate reference and dark measurements, as well as consideration of stray light, signal noise, and potentially overlapping diffraction orders.

Can I use the DIY spectrometer to identify plastics or other materials?

The DIY spectrometer can be used for experimental investigations of the spectral properties of different materials.

In the visible spectral range, differences in absorption, transmission, or fluorescence can be investigated, for example. Measurements in the near-infrared are also possible in principle.

However, reliable identification of many plastics, rubber compounds, and other organic materials often relies on characteristic absorption bands in the mid-infrared (MIR). These lie outside the sensitivity range of the silicon CCD sensor used in the spectrometer.

Material analysis is also possible in the near-infrared. Depending on the application, however, this generally requires a considerably broader wavelength range, suitable reference spectra, and chemometric analysis methods.

Whether the DIY spectrometer is suitable for distinguishing between specific materials therefore depends strongly on their spectral properties and the particular measurement task.

Examples of experimental investigations of different light sources and materials can be found in our collection of spectroscopic application examples.

Is the DIY spectrometer suitable for industrial process monitoring?

EURECA's DIY spectrometer was primarily designed for education, research, development, and experimental laboratory applications.

Its open, modular design allows optical components to be exchanged, custom measurement setups to be developed, and different spectroscopic techniques to be investigated. This makes it particularly suitable for feasibility studies and the development of new measurement concepts.

For continuous operation in industrial production environments, however, we recommend spectrometer modules specifically designed for such applications.

For these applications, EURECA offers compact microspectrometers with integrated diffraction gratings, as well as other optoelectronic components and customized solutions.

The most suitable technology for a particular application depends primarily on the required spectral range, measurement speed, spectral resolution, and environmental conditions.

Last update: 2026-11-16